Aquascape's Bullet Spotlight's compact size and powerful output makes it an extremely versatile fixture.  The Bullet Spotlight is ideal for highlighting focal points and can be used in and out of the water.

• Includes two different mounting platforms, adjustable stand, and stake
• Compact design also allows the fixture to be tucked between the rock walls allowing the light to virtually disappear in the water feature.  The Bullet Spotlight is also great for AquaBasin decorative features
• Comes standard with a single warm high output white LED bulb
• Replaceable diodes are available in white, red, blue, green, yellow
• 15’ cord with quick connect plug is included

*Transformer sold separately

• Installation Instructions
  
  Package Includes:
  
  • Bullet L.E.D. light with 15 ft. cord
  • Adjustable plastic light stand and stake.Optional Accessories for the Bullet LED. Light (sold separately)
  • 5 interchangeable colored L.E.D.s (blue, red, green, and yellow)
  • Low Voltage Transformer
  
  WARNING
  
  It is good practice whenever working in or near water to have all electrical devices plugged into a ground fault circuit interrupter(GFCI) that has been installed by a licensed electrician. Do not put stake through liner. COVER TO LIGHT MUST BE TIGHT AT ALL TIMES TO PREVENT ANY LEAKING.
  
  Legal Warnings
  
  Except as stated in the warranty, there are no other representatives or warranties related to the product or its use. THE USER SHALL DETERMINE THE SUITABILITY OF THE PRODUCT FOR THE USER’S INTENDED USE, AND THE USER ASSUMES ALL RISKS AND LIABILITIES WHATSOEVER IN CONNECTION THEREWITH. Seller and manufacturer’s only obligation is to repair and or replacement of submersible light housing as stated below. ALL IMPLIED WARRANTIES ARE HEREBY EXCLUDED, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Neither seller nor the manufacturer shall be liable for any injury loss, or damage whether direct, incidental, or consequential arising out of the use or inability to use the product. The national Electric Code, Article 680-14 (A), requires a Ground Fault Circuit Interceptor (GFCI) to be installed in the branch circuit supplying fountain equipment rated above 15 volts.
  
  1YEAR WARRANTY
  
  The LED Bullet Spotlight is warranted against defective materials and workmanship for a period of 12 months from the date of purchase by the user. Contact the installer or place of purchase if the LED Bullet Spotlight should fail within the warranty period. Warranty shall be totally null and void in the event the LED Bullet Spotlight is abused, misused, or used for a purpose other than for which the product is intended. No warranty applies to the light bulb used with the housing.
  
  Installing the Light
  
  It is easiest to install and conceal the Bullet L.E.D. light(s) prior to putting the gravel in the Pond and stream. Find a desirable location for the light(s). We suggest positioning the lights so they are facing away from the main viewing area. Double-check to make sure that the cover is fastened tightly down. Depending on the installation, the Bullet Light can be used in or out of water. If being used out of water attach the light to the stake, if being used in the stream area the light should be used with the light stand. Simply take the cord and plug into the transformer, plug in transformer and enjoy! The Bullet Light can also be wired directly into a pre-existing low voltage lighting system. In order to do this, cut off the plug on the light and splice directly into the low voltage wire.
  
  Replacing the Light Bulb
  
  1. Make sure all power is shut off to the light before changing the bulb. The light housing must be above water to properly service the light bulb. 2. Unscrew the ring nut from the front of the light housing unit. 3. Remove the glass lens and o-ring from light housing. 4. Remove the L.E.D. bulb.5. Insert the new bulb6. The o-ring and lens can now be installed back into place. Make sure there is no dirt or debris on the lens, o-ring, and assembly prior to reassembling.7. Attach the ring nut onto the light housing.8. Test to make sure light works9. Position light back into pond.
  
  Troubleshooting
  
  • Make sure that the plug is inserted all the way into the transformer. If light is wired into a low voltage lighting system make sure all of the connections are sound.
  • Make sure that no water has got into light housing unit.
  • Check light bulb.
  • Bulb life can be greatly increased by setting timer on transformer so the light only operate during the desired times.