• Powerful 20-watt low voltage light with 15 ft. cord
• Comes with 5 interchangable lenses
(clear, blue, green, red, amber)
• Includes adjustable light stand
• For submerged use only
• Includes quick-connect plug or can be hard-wired

• Installation & Maintenance Instructions
  
  Legal Warnings
  
  Except as stated in the warranty, there are no other representatives or warranties related to the product or its use. THE USER SHALL DETERMINE THE SUITABILITY OF THE PRODUCT FOR THE USER’S INTENDED USE, AND THE USER ASSUMES ALL RISKS AND LIABILITIES WHATSOEVER IN CONNECTION THEREWITH. Seller and manufacturer’s only obligation is to repair and or replacement of submersible light housing as stated below. ALL IMPLIED WARRANTIES ARE HEREBY EXCLUDED, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Neither seller nor the manufacturer shall be liable for any injury loss, or damage whether direct, incidental, or consequential arising out of the use or inability to use the product. The national Electric Code, Article 680-14 (A), requires a Ground Fault Circuit Interceptor (GFCI) to be installed in the branch circuit supplying fountain equipment rated above 15 volts.
  
  WARNING!
  
  It is good practice whenever working in or near water to have all electrical devices plugged into a ground fault circuit interrupter(GFCI) that has been installed by a licensed electrician. Do not put stake through liner. Spot light MUST be completely submerged in water for proper cooling of light bulb. COVER TO LIGHT MUST BE TIGHT AT ALL TIMES TO PREVENT ANY LEAKING.
  
  1) Getting to Know Your MicroSpot™ Light
  
  The MicroSpot™ Light comes with:
  20 Watt underwater light with 15 ft. cord
  • 5 interchangeable lenses (clear, blue, red, green, and amber)
  • Adjustable plastic light stand.
  
  The MicroSpot™ Light with transformer comes with:
  • 5 interchangeable lenses (clear, blue, red, green, amber, and red)
  • Adjustable plastic light stand.
  • Transformer
  
  2) Installing the Light
  
  It is easiest to install and conceal the MicroSpot™ light(s) prior to putting the gravel in the pond. Find a desirable location for the light(s). We suggest positioning the lights so they are facing away from the main viewing area. Double-check to make sure that the cover is fastened tightly down. The light is designed to be incorporated into the boulder wall by “tucking” it in-between a set of boulders. The boulders can be adjusted around the light in order to “lock” light into position. Simply take the cord and plug into transformer, plug in transformer and enjoy! MicroSpot™ 20 Watt light is designed to be used COMPLETELY submerged in water. Be careful to not place light fixture in the “ice-zone” of the pond, this may cause cracked lenses. We suggest placing the light fixture 8 inches or more below the surface of the water. You can place the fixture in the “ice-zone” as long as you remove it before winter ad leave outside the pond or in a position that it will not freeze in the pond. Replacement lenses are available if needed.
  
  3) Replacing the Light Bulb
  
  1. Make sure the transformer is unplugged before changing the bulb. The light housing must be above water to properly service the light bulb.
  2. Unscrew the plastic cap from the front of the light housing unit.
  3. Remove the glass lens and o-ring from light housing.
  4. Use a thin flat-head screwdriver to pry the light up and out of the housing. Note: Removing the halogen light by pulling the bulb is not recommended.
  5. Insert the new bulb by inserting the two metal plugs into the connector. Note: Do not touch the halogen light inside the assembly.
  6. The o-ring and lens can now be installed back into place. Make sure there is no dirt or debris on the lens, o-ring, and assembly prior to reassembling.
  7. Attach the cap back onto the light housing.
  8. Test to make sure light works
  9. Position light back into pond.
  
  4) Troubleshooting
  
  • Make sure that the plug is inserted all the way into the transformer.
  • Make sure that no water has got into light housing unit.
  • Check light bulb.
  • Bulb life can be greatly increased by setting timer on transformer so the light only operate during the desired times.
  
  5) Replacement Parts List
  
  • Replacement Bulb-20 Watt - Item #22200
  • Replacement Clear Lens - Item #99532
  
  1 YEAR WARRANTY
  
  The submersible light housing is warranted against defective materials and workmanship for a period of 12 months from the date of purchase by the user. Contact the installer or place of purchase if the submersible light housing should fail within the warranty period. Warranty shall be totally null and void in the event the submersible light
  housing is abused, misused, or used for a purpose other than for which the product is intended. No warranty applies to the light bulb used with the housing.